DIESEL HEAVY VEHICLE

INTERNATIONAL

VERSION：v7.44

Basic functions：

  1. Read ECU Information
  2. Read Fault Code
  3. Erase Fault Code
  4. Live Data

 

Actuation Test：

1.KOEO Test

1.1 Standard Test

1.2Output State Low Test

1.3 Output State High Test

1.4 Injector Test

1.5 Continuous Monitor test

1.6 Intake Air Heater Test

1.7 Relative Compression Test

2.KOER Test

2.1 Standard Test

2.2 Air Management Test

2.3 Cylinder Cutout Test

2.4 Engine Run Up Test

2.5 High Pressure Pump Test

2.6 Injector Disable Test

2.7 VGT Output State Test Low

2.8 VGT Output State Test Medium

2.9 VGT Output State Test High

3.KOER Aftertreatment Test

3.1 Onboard Filter Cleanliness Test

3.2 DSI System Test

3.3 AFT Flow Test

3.4 AFS Leak Test

3.5 AFT System Leak Test

 

Special functions：

  1. Transmission Setup
  2. Engine Warn Protection System
  3. Road Speed limiting/Cruise Control
  4. PTO
  5. Greardown Protection
  6. Speedo,Tire,Axle Setup
  7. Progressive Shift
  8. Driver Rewards
  9. Idle Shutdown Timer
  10. Engine Fan
  11. Momentary Road SPeed Limiting
  12. Customer Password
  13. Service Interval
  14. O2 Sensor Calibration
  15. Injector Quantity Adjustment

 

 

VOLVO

VERISON：v7.13

Basic functions：

  1. Read ECU Information
  2. Read Fault Code
  3. Erase Fault Code
  4. Live Data

 

Special functions：

  1. Injector Cut Out, Manual
  2. Cylinder Compression, Test
  3. Learned Data Reset
  4. Oil Pressure Test(During Cranking)
  5. Cylinder Balancing, Test
  6. Draining Water in the Fuel, Test
  7. Engine Brake Function, Test
  8. Diesel Particulate Filter Service Regeneration
  9. Parameter.Programming

9.1 .Engine Brake

9.2 .Engine Fan Controls

9.3 .Engine Governor

9.4 .Engine Protection

9.5 .Engine Speed Limit

9.6 .Engine Torque Limit

9.7 .Fuel Economy Incentive Program

9.8 .Engine Idle Settings

9.9 .Idle Shutdown [Includes Idle Cooldown]

9.10 .Auxiliary/ Engine Remote Start/Stop

9.11 .Injection Control

9.12 .Misc Engine Settings

9.13 .Misc Vehicle Settings

9.14 .Engine Speed Control (ESC)

9.15 .Electronic Hand Throttle (EHT)/ PTO 0

9.16 .Power Take-Off #1 (PTO 1)

9.17 .Power Take-Off #2 (PTO 2)

9.18 .Power Take-Off #3 (PTO 3)

9.19 .Power Take-Off #4 (PTO 4)

9.20 .Cruise Control

9.21 .Road Speed Limit

9.22 .Tamper Detection

9.23 .Theft Deterrent

9.24 .System Warning

9.25 .Driver Alert Systems

9.26 .Driver Display Settings

9.27 .Brake

9.28 .Air Pressure Management

9.29 .Auto Neutral

9.30 .Exterior Light & Headlight

9.31 .Datamax

9.32 .Muddy Site

9.33 .Electronically Controlled Suspension (ECS)

 

 

 

MACK

VERSION：v7.13

Basic functions：

  1. Read ECU Information
  2. Read Fault Code
  3. Erase Fault Code
  4. Live Data

 

Special functions：

  1. Injector Cut Out, Manual
  2. Cylinder Compression, Test
  3. Learned Data Reset
  4. Oil Pressure Test(During Cranking)
  5. Cylinder Balancing, Test
  6. Draining Water in the Fuel, Test
  7. Engine Brake Function, Test
  8. Diesel Particulate Filter Service Regeneration
  9. Parameter.Programming

9.1 .Engine Brake

9.2 .Engine Fan Controls

9.3 .Engine Governor

9.4 .Engine Protection

9.5 .Engine Speed Limit

9.6 .Engine Torque Limit

9.7 .Fuel Economy Incentive Program

9.8 .Engine Idle Settings

9.9 .Idle Shutdown [Includes Idle Cooldown]

9.10 .Auxiliary/ Engine Remote Start/Stop

9.11 .Injection Control

9.12 .Misc Engine Settings

9.13 .Misc Vehicle Settings

9.14 .Engine Speed Control (ESC)

9.15 .Electronic Hand Throttle (EHT)/ PTO 0

9.16 .Power Take-Off #1 (PTO 1)

9.17 .Power Take-Off #2 (PTO 2)

9.18 .Power Take-Off #3 (PTO 3)

9.19 .Power Take-Off #4 (PTO 4)

9.20 .Cruise Control

9.21 .Road Speed Limit

9.22 .Tamper Detection

9.23 .Theft Deterrent

9.24 .System Warning

9.25 .Driver Alert Systems

9.26 .Driver Display Settings

9.27 .Brake

9.28 .Air Pressure Management

9.29 .Auto Neutral

9.30 .Exterior Light & Headlight

9.31 .Datamax

9.32 .Muddy Site

9.33 .Electronically Controlled Suspension (ECS)

 

 

 

DIESEL ENGINE

CUMMINS

VERSION：V8.20

SYSTEM COVERAGE：

  1. Cummins diesel engines(J1708)
  2. Cummins diesel engines(J1939)

 

Basic functions：

  1. Read ECU Information
  2. Read Fault Code
  3. Erase Fault Code
  4. Freeze Frame Data
  5. Read Data Stream
  6. Action test
  7. Features and Parameters
  8. Trip Information
  9. Advanced ECM Data

 

Action test：

1.Aftertreatment Diesel Exhaust Fluid Pump Heater Test

2.1.Aftertreatment Diesel Exhaust Fluid System Leak Test

3.Aftertreatment Diesel Particulate Filter Regeneration

4.Aftertreatment SCR Performance Test

5.Aftertreatment High NOx Reset

6.Aftertreatment SCR Catalyst Desulphurization

7.Cylinder Cutout Test

8.Diesel Exhaust Fluid Doser Pump Air Solenoid Click Test

9.Diesel Exhaust Fluid Doser Pump Override Test

10.Diesel Exhaust Fluid Doser System Heater Test

11.EFC Actuator Override Test

12.Electric Fuel Lift Pump Override Test

13.Engine State Monitor

14.Fan Override Test

15.Fast Idle Warmup Test

16.Fuel Injector Performance Test

17.Fuel System Leakage Test

18.Intake Air Heater Override

19.SAE J1939 Datalink Control Test

20.Setup for Dynamometer

21.Starter Lockout Relay Driver Override Test

22.VGT Electronic Actuator Installation and Calibration

23.VGT Hysteresis Test

24.Aftertreatment Shutoff Valve and Injector Override Test

25.Centinel Operational Test

26.Dual Fan Clutch Test

27.Gas Throttle Control Test

28.Heated Oxygen Sensor Test

29.Injector Check Valve Diagnostics Test

30.Power Generation Tuning Test

31.Engine Protection Witness Test

Features and Parameters

1.System ID and Dataplate

2.Accelerator Interlock

3.Accelerator Options

4.Accelerator Options

5.Adjustable Low Idle Speed

6.AEM Trend Log

7.Aftertreatment

8.Aftertreatment Diesel Particulate Filter Regeneration Inhibit Lamp

9.Air Conditioner Control

10.Air Conditioner Switch

11.Air Shut Off Valve

12.Alternate Torque

13.Alternator Failure Warning

14.Anti-Lock Brake (ABS) Controller

15.Automatic Boost Power

16.Auxiliary Governor Control

17.Battery Power Required Lamp

18.Boost Power

19.Broadcasted Percent Power

20.Centinel Oil System

21.Charge Air Cooler Outlet Temperature Sensor

22.Clutch Pedal Position Switch

23.Clutch Protection

24.Cold Idle Warmup

25.Constrained Operation

26.Compressor Intake Density Torque Derate

27.Crankcase Ventilation Heater

28.Cruise Control

29.Cruise Control

30.Cruise Control and Engine Brake Interaction

31.Customer Constrained Operation

32.Cyclical Load Acceptance Gain Adjust

33.Dedicated Fault Lamps

34.Dedicated Pulse Width Modulation Output

35.Driver Reward

36.Driver Reward

37.Dual Fan Clutch Control

38.Dual Outputs Based On Sensed Parameters

39.Electric Fuel Lift Pump

40.Electrical System Voltage

41.Engine Brake Control

42.Engine Coolant Level Sensor

43.Engine Coolant Level Sensor 2

44.Engine Oil Level

45.Engine Oil Pressure Sensor

46.Engine Overload Protection

47.Engine Protection

48.Engine Rebuild Run Time

49.Engine Speed Cruise Control

50.Engine Start Stop Permit

51.Engine Warmup Protection

52.Enhanced Auxiliary Shutdown Switch

53.Ether Injection Enable

54.Fan Control

55.Fan Control

56.Fault Acknowledge Switch Enable

57.Fast Idle Warmup

58.Final Inducement Restart

59.Frequency Accelerator Pedal or Lever

60.Fuel Filter Restriction Indicator Switch

61.Fuel Grade Enable

62.Fuel Level Sensor 2

63.Fuel Usage Adjustment

64.Gear Down Protection

65.Governor Type

66.High NOx Reset

67.High Pressure Common Rail Injector Setup Enable

68.High Soot Load Shutdown

69.High Sulphur Protection Inhibit

70.Idle Rampdown

71.Idle Shutdown

72.Idle Shutdown

73.Idle Shutdown

74.Immobilizer

75.Inducement Override Switch

76.Intake Air Heater

77.Intermediate Speed Control

78.Intermediate Speed Control

79.J1939 Controls

80.Load Based Acceleration Control

81.Load Based Speed Control

82.Load Based Speed Control

83.Load Based Speed Control - Enhanced

84.Maintenance Monitor

85.Multi Function Switch Enable

86.Multiple Unit Synchronization

87.OEM Ambient Air Temperature Sensor

88.OEM Auxiliary Pressure Sensor Fault Threshold

89.OEM Auxiliary Switch Input

90.OEM Auxiliary Temperature 2

91.OEM Simple Lockout

92.OEM Switch 1

93.OEM Switch 2

94.OEM Switch 3

95.OEM Switch 4

96.OEM Switch 5

97.Oil Level Electronic Dipstick

98.Oil Level Sensor Enhanced

99.Parking Brake Switch

100.Powertrain Protection

101.Powertrain Protection

102.Powertrain Protection

103.Primary  Accelerator Pedal Or Lever

104.PTO

105.Rated Overspeed Protection

106.Rated Speed Adjust

107.Remote Accelerator Pedal or Lever

108.Remote Start

109.Road Speed Governor

110.RS422 Communication

111.SAE J1939 Multiplexing

112.Service Brake Switch

113.Service Brake Validation Switch

114.Single Bank Cutout

115.Smart Torque 2

116.Starter Lockout

117.Starter Control

118.Sudden Deceleration Event Settings

119.Switched Alternate Low Idle Speed

120.Switched Droop

121.Switched Droop

122.Switched Maximum Engine Operating Speed

123.Tire Wear Adjustment

124.Transmission Accelerator Interlock

125.Transmission Setup

126.Transmission Setup

127.Trip Information

128.Trip Information

129.User Adjustable Fuel Economy

130.Variable Rate Vehicle Acceleration Management

131.Vehicle Acceleration Management

132.Vehicle Speed Based Device Driver A

133.Vehicle Speed Based Driver B

134.Vehicle Speed Sensor Anti-Tampering

135.Vehicle Speed Sensor Anti-Tampering

136.Vehicle Speed Sensor Anti-Tampering

137.Vehicle Speed Source

138.Vehicle Speed Source

139.Water In Fuel Sensor

Advanced ECM Data

1.Aftertreatment Maintenance

2.Aftertreatment Maintenance Filter Installation

3.Aftertreatment Particulate Matter Sensor Regeneration

4.Aftertreatment SCR Catalyst Cold Soak Override

5.Diesel Exhaust Fluid Doser Purge Counter

6.Duty Cycle Monitor

7.Fuel Consumption Monitor

8.Fuel Injector Reset

9.Fuel System Table Reset

10.High Pressure Common Rail Injector Setup

11.Hybrid Engine Start Stop Override

12.Idle Shutdown Override

13.Immobilizer Installation

14.Maintenance Monitor

15.Turbocharger Actuator Compatibility

16.Vehicle Classification

 

 

CATERPILLAR

VERSION：v6.72

SYSTEM COVERAGE：

A: CAT TURCK / BUS

B: CAT Construction Machinery

C: CAT HD(J1708)

A: CAT TURCK / BUS

Basic functions：

  1. Read ECU Information
  2. Read Fault Code
  3. Read Data Stream
  4. Actuation Test

 

Special functions：

Group 1:

  1. Configuration group 1
  2. Machine optional components
  3. Auxiliary hydraulic optional component configuration
  4. Control input installation
  5. Driving speed shift parameters
  6. Throttle knob engine speed
  7. Throttle knob hydraulic power percentage
  8. Recommended maintenance intervals

 

Group 2:

  1. Configuration
  2. Injector data
  3. Cylinder cutoff functions

 

Group 3:

  1. Selected Engine Rating
  2. ECM Identification Parameters
  3. Security Access Parameters
  4. Vehicle Speed Parameters
  5. Cruise Control Parameters
  6. Idle Parameters(Old PTO)
  7. Dedicated PTO Parameters
  8. Engine/Gear Parameters
  9. Timer Parameters
  10. Smart Idle Parameters
  11. Engine Monitoring Parameters
  12. Trip Parameters
  13. Vehicle Activity Report parameters
  14. Driver Reward
  15. Input Selections
  16. Output Selections
  17. Data Link Parameters
  18. System Settings

B: CAT Construction Machinery

1. Read ECU Information

2. Read Fault Code

3. Erase Fault Code

4. Read Data Stream

5. Actuation Test (Injector solenoid valve test).

6. Special Function (Vehicle Speed Parameters, Idle Parameters, Timer Parameters)

C: CAT HD(J1708)

1. C15 Truck

2. C12 Truck(Air Inlet Shutoff\ Diese-Dual Fuel\ Gas-Dual Fuel)

3. C16 Truck

4. C18 Truck

5. 3406E(Truck\ IND\ MAR\ Truck AIS)

6. C10 Truck

7. 317B(Truck\ MAR\ Challenger)

8. 3116 Truck

9. 3126 Truck

 

 

DETROIT

VERSION：v6.12

SYSTEM COVERAGE：

  1. DDDL7 (EPA07 and EPA10 engines)
  2. DDDL6 (EPA04 and earlier engines)
  3. DD13/DD15
  4. Series 60(6067HG6E)
  5. Series 60(6067HV6E)
  6. Series 60(6067MK60)
  7. Series 60
  8. Series 55
  9. Series 50
  10. Series 30
  11. V92 RH rotation
  12. V92 LH rotation
  13. V149 RH rotation
  14. V149 LH rotation
  15. I71 RH rotation
  16. I71 LH rotation
  17. V71 RH rotation
  18. V71 LH rotation
  19. V149 RH rotation
  20. V149 LH rotation
  21. V2000 RH rotation
  22. V4000 RH rotation
  23. V4000 LH rotation
  24. Vitas Motori
  25. V53 LH rotation
  26. V53 RH rotation
  27. MBE 900(4)
  28. MBE 900(6)
  29. MBE 4000(6)
  30. OM 501(6)
  31. OM 502(8)

 

Basic functions：

  1. Read ECU Information
  2. Read Fault Code
  3. Erase Fault Code
  4. Read Data Stream

 

Action test：

  1. All Services
  2. Activate Outputs
  3. DPF System
  4. Idle Speed Balance
  5. Intake Throttle Valve
  6. Voltages
  7. Cylinder Cutout(Automatic)
  8. Cylinder Cutout(Manual)
  9. Fan Diagnostic
  10. FIS Low Pressure Leak Test
  11. Fuel System Integrity Check
  12. FIS Fuel Filter
  13. FIS Water in Fuel
  14. FIS Leak Detection

 

Special functions：

  1. All Parameters
  2. Fuel Economy
  3. Speed Limiter
  4. PTO
  5. Progressive shift
  6. Optimized Idle
  7. Inputs and Outputs
  8. Idle and PTO Shutdown
  9. Cruise Control
  10. Engine Brake Config
  11. Engine Protection
  12. Fan
  13. Fleet Management
  14. Injector Codes

 

 

 

 

 

ABS + TRANSMISSIONS

ALLISON (T)

VERSION：v5.32

SYSTEM COVERAGE：

  1. 1000/2000 Product Families(4th Generation)
  2. 3000/4000 Product Families(4th Generation)
  3. Product Families(Pre-4th Generation)
  4. 1000/2000 Product Families(5th Generation)
  5. 3000/4000 Product Families(5th Generation)
  6. CEC3-5610,6610,8610,9610,9810
  7. TC10
  8. WTEC II
  9. WTEC III

 

Basic functions：

  1. Read ECU Information
  2. Read Fault Code
  3. Erase Fault Code
  4. Read Data Stream
  5. Actuation Test

Actuation Test

1.   Solenoid Test

2.   Reset Adaptive Shift Parameters

3.   Reset Fast Adaptive

4.   Reset Throttle Calibration

5.   Lamp Tests

6.   Reset Auto-Detect

7.   Reset Auto Detect Retarder

8.   Reset SEM Auto-Select

9.   Reset Prognostics Information

                       Reset Oil Life Monitor

Reset Transmission Monitor

 

Special functions：

Input wires

1.   Input-Secondary Mode

2.   Input-Auxiliary Function Range Inhibit

3.   Input-PTO Enable

4.   Input-Engine Brake Enable and Pre-Select Request 1

5.   Input-Auto Neutral Single Input

6.   Input-Lock Up Pump Mode(FTPM)

7.   Input-Reverse Enable

8.   Input-Kickdown Switch

9.   Input-Reverse Inhibit With Preselect Request

10. Input-Service Brake Status Inverted

11. Input-Service Brake Status Non-Inverted

12. Input-4WD Transfer Case Low

13. Input-Grade Braking Disable

14. Input-Overdrive Disable

15. Input-ABS Active

16. Input-Retarder Enable

17. Input-Low Traction Mode

18. Input-Pump Pack Enable

19. Input-RELS

20. Input-Engine Brake and Pre-select Request 2

21. Input-Shift Selector Transition(SST)

22. Input-Shift Selector Transition w/2nd Schedule

23. Input-Aux Function Range Inhibit 1 Special

24. Input-Aux Function Range Inhibit 2 Special

25. Input-Direct Hold

26. Input-Selector Display Blanking

27. Input-Auxiliary Hold

28. Input-Direction Change Enable

29. Input-Auto 2 to 1 Pre-select

30. Input-D1 Selection

31. Input-Auto Neutral Dual Input

32. Input-Automatic Neutral

33. Input-Two Speed Axle Enable

34. Input-Two Speed Axle Monitor

35. Input-Max Range Hold

36. Input-Manual Lockup

37. Input-Manual Lockup Enable

38. Input-Quick to Neutral Oil Field Pump

39. Input-Differential Clutch Request

40. Input-Neutral Very Low Request

41. Input-Brake Based Automatic Neutral

42. Input-Preselect Request

43. Input-High N/V 1

44. Input-High N/V 2

45. Input-Auto Neutral Single Input W/S S Override

46. Input-Idle Start/Stop Input 1

47. Input-Idle Start/Stop Input 2

48. Input-2nd Gear Start

49.                 Input-Garage Shifts to 2nd Reverse

 

Output wires

                1.            Output-PTO Enable

                2.            Output-Engine Brake Enable-Inverted

                3.            Output-Engine Brake Enable - Non-Inverted

                4.            Output-Range Indicator

                5.            Output-Output Speed Indicator A

                6.            Output-Retarder Indicator

                7.            Output-Sump Temp Indicator

                8.            Output-Secondary Mode Indicator

                9.            Output-Range Inhibit Indicator-RLL

                10.          Output-ABS Indicator

                11.          Output-Overdrive Disable Indicator

                12.          Output-Low Traction Indicator

                13.          Output-Two Speed Axle Indicator

                14.          Output-Lockup Indicator

                15.          Output-Output Speed Indicator B

                16.          Output-Engine Overspeed Indicator

                17.          Output-PTO Overspeed Indicator

                18.          Output-Differential Clutch Indicator

                19.          Output-Neutral Indicator for PTO

                20.          Output-Strip Selector Range Indicator

                21.          Output-T-Case 4WD Low Indicator

 

Reprogramming CMCs

                1.            PTO Enable

                2.            Automatic Neutral for PTO

                3.            PTO Overspeed Indicator

                4.            Engine Brake and Pre-Select Request

                5.            Range Indicator

                6.            Output Speed Indicator A

                7.            Output Speed Indicator B

                8.            Engine Overspeed Indicator

                9.            Sump/Retarder Temp Indicator

                10.          D1 Selection

                11.          Overide Autodetect

                12.          Retarder Parameters

                13.          Two Speed Axle Enable

                14.          Neutral Indicator for PTO

                15.          Auto Neutral for Refuse Packer

                16.          Brake Based Automatic Neutral

                17.          Preselect Request

                18.          Prognostics

                19.          VAC

BENDIX (T)

VERSION：v5.00

SYSTEM COVERAGE：

  1. EC-17
  2. EC-30
  3. EC-60

 

Basic functions：

  1. Read ECU Information
  2. Read Fault Code
  3. Erase Fault Code
  4. Read Data Stream
  5. Actuation Test

 

Special functions：

  1. Controller Configuration
  2. Rest ABS Controller
  3. Dyno Mode

 

WABCO (A)

VERSION：v5.60

SYSTEM COVERAGE：

  1. Tractor ABS Diagnosis
  2. Hydraulic ABS Diagnosis

Special functions：

  1. Read ECU Information
  2. Read Fault Code
  3. Erase Fault Code
  4. Live Data
  5. Actuation Test

 

 

ZF (T)

VERSION：v5.00

Basic functions：

  1. Read ECU Information
  2. Read Fault Code
  3. Erase Fault Code
  4. Live Data
  5. Actuation Test